עמוד ראשי  |  התחבר או אם אינך עדיין רשום, הרשם בחינם.
  בלוגר  
אודות
קבלת עדכונים
רוצים לקבל הודעה במייל בכל פעם שהבלוג שלי מתעדכן ?

עדכוני RSS
חיפוש
נושאים
ארכיון
Prospects for the development of micro-grindin
04/07/2018 09:08
posuiman
ultrafine mill

Ultrafine Mill is also a kind of ore crushing machinery. Its technology is a new crushing engineering technology developed in recent years along with modern high technology and new materials industry. It has become the most important industrial mineral and other raw materials. One of the deep processing technologies is of great significance to the development of modern high-tech industries. However, at present, there is still a certain gap between our domestic micro-grinding and foreign relatives. Therefore, the future development direction of micro-grinding is mainly reflected in the following aspects:

It is necessary to improve the existing SCM Ultrafine Mill structure, improve the crushing ability of the micro-grinding to medium-hard ore and the convenience of equipment maintenance, and mainly focus on the improvement of the plate hammer and rotor structure to facilitate the replacement and loading of the hammer; the counter-attack Structural optimization of the (broken cavity shape) improves the primary crushing rate and energy utilization of the ore. Research and development of new plate hammer materials with high wear resistance and high toughness to improve the service life of the plate hammer and improve productivity.

The application of modern mechatronics technology and modern control methods (such as hydraulic technology, electronic technology), continuously improve the automation of micro-grinding, reduce the labor intensity of workers and increase productivity. For example, the application of modern computer-aided design optimizes the structural parameters of the counter-attack frame to improve the energy utilization rate and the primary crushing rate of the ore. In order to meet the needs of the market and customers, ultrafine mill is being serialized and standardized.

Adhere to technological innovation and gradually get rid of the single introduction and imitation of products. The ultra-fine grinding powder produced by our company has the advantages of small floor space, high efficiency, energy saving, convenient maintenance, environmental protection and cleanliness, high reliability, etc., and is highly praised by users. After the ore materials are ground, they are applied in many industrial fields. For example, calcite, dolomite, limestone, mica stone and other ore are used in the industrial application. There is a lot of knowledge about the application of grinding ore materials after grinding.

0 תגובות
Mobile construction waste crusher structure
29/06/2018 05:50
posuiman
construction waste crusher

The mobile Construction Waste Crusher is mainly composed of a body, a rotor, a counterattack board, and a spring buffer device. The body of mobile construction waste crusher is divided into upper and lower parts. The lower body is directly mounted on the foundation, and a small door is opened on the upper body for inspection and repair. Wherever the inner wall of the body may come into contact with the material, high manganese steel wear-resistant lining plates are embedded. Both ends of the rotor shaft are supported on self-aligning spherical roller bearings on both sides of the machine body. The rotor shaft passes through the inner wall of both sides of the body and is equipped with a sealing device to prevent coal dust from being lifted. The crushing hammer is rigidly connected to the rotor. When tapping the material, it can fully utilize the energy of the entire rotor.

Mobile Construction Waste Crusher generally has two counterattack plates. One end of the counterattack board is hung on the upper part of the body through the pin, and the other end is connected with a special screw. A compression spring is arranged on the screw and the counter plate is controlled at a certain position. The gap between the rotor plate hammer and the counter plate can be adjusted by the nut at the tail of the screw. When the non-broken material falls into the crushing chamber, the counterattack plate is subjected to a great deal of pressure, so that the screw further compresses the spring, thereby increasing the gap between the counterattack plate and the plate hammer, so that the non-crushed material is discharged. After that, the counterattack plate is restored to its original position under the action of its own weight and spring force, and the crushing work continues.

Different from the hammer crusher, the hammer and rotor of the mobile construction waste crusher are rigidly connected together, and there is a large crushing counter cavity and no purlin components. Therefore, the crushing effect of the material is good, and the wear is lower than the hammer crusher. However, the disadvantage is that the striking plate and the counterattack plate are easily worn and the working noise is high.

0 תגובות
Ore milling equipment of potassium feldspar
30/05/2018 06:31
posuiman
milling

Potash feldspar is an alkali metal or Ore milling equipment alkaline earth metal aluminate mineral such as potassium, sodium, calcium, and may also be referred to as orthoclase. Potassium feldspar is usually present in meat red, yellowish white or gray, and is widely used in agriculture, construction, chemical industry and other fields. K-feldspar ultra-fine grinding is mainly used for the crushing of broken feldspar materials.

In the growing market for mining machinery and equipment, many manufacturers of ultra-fine potassium feldspar mills have given users more choices. If you choose more than one, you will inevitably have the Ore milling equipment feeling that you are not sailing at all. It is also easy to pick up equipment that is not worth the price.

Our company is a professional manufacturer of ultrafine grinding of potash feldspar. Here, we will tell you about some points of purchasing ultrafine grinding of potash feldspar. In addition to manufacturers, prices and other factors need to be carefully identified by the user, the quality of the K-feldspar ultra-fine grinding itself requires the user to carefully distinguish, liner and grinding ball as an important part of the ultrafine grinding of potassium feldspar, the quality of the impact The overall quality, efficiency, and service life of ultra-fine potassium feldspar mills.

0 תגובות
Benefit of Proper Lubrication of Modern Machin
30/03/2018 08:44
posuiman
ore milling equipment

The performance of modern Ore Milling Equipment plant and machinery depends to a large extent upon the reliability of rolling bearings. One of the major contributing factors to achieving high reliability is proper lubrication. Bearing lubricants fall into three main categories – oils, greases and solid dry film lubricants. They are usually limited to moderate speed and very light loading conditions. Greases, because of their convenience, are by far the most widely used of the three and have been the focus of much development over the last decade. Besides supporting the load the lubricant may have to perform other functions on the cone crusher as well, for instance it may cool the contact areas and remove wear products. While carrying out these functions the lubricant is constantly replaced from the contact areas either by the relative movement (hydrodynamics) or by externally induced forces.

Bearings operate on very thin films of Ore Milling Equipment lubricant which have to be maintained in order to ensure that the bearing's design life is achieved. The three primary principles of maximizing bearing life are: selecting the correct lubricant; applying the lubricant properly; and maintaining the lubricant in a clean condition. Adequate lubrication allows smooth continuous operation of equipment, with only mild wear, and without excessive stresses or seizures at bearings. When lubrication breaks down, metal or other components can rub destructively over each other, causing destructive damage, heat, and failure. Neglect or failure in any of these three areas will greatly increase the risk of premature bearing failures and will interfere with the trouble-free running that is of crucial importance in modern plant and dryer machine in an increasingly competitive, global market.

The increased speeds and higher temperatures, at which modern Ore Milling Equipmentbearings routinely operate, combined with the demands placed upon them for improved accuracy and reliability, mean that the process of selecting a suitable bearing lubricant today is more critical than ever. In some applications, such as piston engines, the film between the piston and the cylinder wall also seals the combustion chamber, preventing combustion gases from escaping into the crankcase.

0 תגובות
Introduction to Different Kinds of Cone Crushe
21/03/2018 05:37
posuiman

Cone crusher is the most suitable Construction Waste Crusher researched and developed by Machinery for crushing various kinds of mid-hard and ultra-hard ores and rocks. It features many distinguished advantages such as high productivity and quality, easy adjustment and maintenance, reliable construction and low operational costs and it is similar to gyratory crusher in operation with less steepness in the crushing chamber and more of a parallel zone between crushing zones. This cone crushing machine can be classified into spring cone crusher, and hydraulic one, and single-cylinder hydraulic crusher according to their different operation principles and the mechanical devices.

A spring Construction Waste Crusher is composed of frame, transmission device, hollow eccentric shaft, bowl-shaped bearing, crushing cone, springs and hydraulic pressure station for adjusting discharge opening, which covers a wide range in the industry of metallurgy, construction, chemical industry, phosphate industry, etc. for the crushing of iron core, copper ore, limestone, quartz, granite, basalt, and diabase. All of these can help you to achieve the highest level of profitability. Established in 1986, we have steadily grown and developed into being the bellwether of crushing equipment and sand producing machine, ore dressing and powder grinding equipment manufacturer with a complete production line of crushing, grinding and screening.

Hydraulic Construction Waste Crusher equipment is the ultimate solution for the secondary crushing of hard rocks, ores and minerals in order to achieve uniform product size and granularity, the outer shells and the other body components of it are made out of the finest quality steel castings and its robust design helps withstand high crushing loads. The main shaft and eccentric system is made out of high grade forged alloy steel and precision. This series crusher offer several outstanding features such as excellent tramp release system, unique hydraulic lifting system, and high crusher throw and reasonable cavity design, all of these features ensure the cone crusher can offer the unbeatable performance in secondary, tertiary and quaternary applications.

0 תגובות
How to Lower Cost for the Milling Equipment In
08/03/2018 05:37
posuiman

For the Ore Milling Equipment machinery industry, by lowering costs, a company can increase productivity, empower employees and turn a greater profit. The upsides are incredible, but the process of lowering costs isn’t always obvious. Here are two measures we can take to realize the highest yield of our mining equipment and production line. 1. To increase operating hours. Higher uptime is often associated with employee dissatisfaction, lower equipment performance, and higher collateral costs. Most mining equipment manufactured today is designed to perform heavy-duty tasks on a continual basis. Shutting down and starting up accumulates vast amounts of wasted time and lost revenue. Improving your uptime will actually lower your costs.

To buy the best quality Ore Milling Equipment. An effective mining machinery plant is built from the foundation of effective equipment. There’s simply no way around this. Properly designed equipment saves time, saves money, and requires little downtime and maintenance. It’s obvious that high-quality equipment will save money. Considering the cost of a machine over the useful life of the machine is important, as lower cost equipment may save you initially, but can be a liability in the long run, making it even more important for struggling companies to do whatever it takes to buy the best solution initially.

If the Ore Milling Equipment machinery production line is located in a deregulated energy market, it is crucial to seek a company that can help you to negotiate lowered costs. Such companies can negotiate bulk energy supply, buyback, and other cost-savings solutions. Keeping costs down in the Milling Equipment machinery is crucial to market success and profitability. You’re bound to save money by implementing at least one of the cost-savings methods outlined above.

0 תגובות
The Crushing Manner of Ore Milling Equipment
26/02/2018 11:17
posuiman

The composition of the single rotor Ore Milling Equipment is relatively simple, and it is mainly composed by the machine rack, driving machine, rotor hammer and the impacting plate. Among them, the rack is made up of the upper rack and the lower rack, and they are connected by the bolt. The part that is on the axial lead of the rotor is called upper rack, on which there are installed the side door and the back door for examination and installation.

The part that is under the axial lead of the rotor is called lower rack, which is fixed on the ground with bolt in order to sustain the weight of the whole Ore Milling Equipment. All the parts that need to touch the rocks inside the rack are installed with changeable wear-resisting lining board. The Ore Milling Equipment mainly uses the impacting theory to realize the selective crushing to the materials, so that the granularity of the final products produced by the machine is good and the qualified rate is very high, so that it is often used for the final crushing in the roadbed and road surface which has higher requirement for the aggregates, and it is also used in the crushing and production process in such industries as building materials, chemistry and mining.

The Ore Milling Equipment mainly relies on the hammer with high rotary speed to impact the materials, and selectively crusher the weak part. The impacted materials will get huge kinetic energy, and after the mutual impact and friction of the impacting plate and the materials, the purpose of further crushing will be achieved and until the final qualified products are screened. With the constant development of the science and technology, the manufacturing technology and materials of the impact crusher will continuously update and change so that it will better satisfy the demands in the modern industry and building industry. As a professional and the best mining machinery manufacturer in China, Machinery is always ready to provide the superior dryer machine with the best quality and the most competitive price.

0 תגובות